ネオ ビークルインターフェース ハードウェア 製品仕様
neoVI FIRE -ファイア-
neoVI RED -レッド-

車載ネットワークツール

ハードウェアneoVI FIREおよびneoVI RED はIntrepid Control Systems社製の車載ネットワーク用通信アダプタです。
同社のアナライザツール Vehicle Spy上でCANやLINの通信データを解析いただけます。

また、neoVI FIRE上にリアルタイム用のスクリプトを搭載して直接実行することにより、 PC上で行った場合に比べてさらに高速なリアルタイム通信を行うことも可能です。
neoVI FIRE / neoVI RED の特徴
・CANとLIN、2種類のネットワークに対応
・0〜3.3Vのアナログ信号に対応
・スタンドアロンでのロギング・リアルタイム通信
・既存のアプリケーションや様々な開発環境への対応
・Vehicle Spyソフトウェアとの連携
・スクリプトの記録・自動実行機能を搭載
・PCレス単体ロギング機能(最初に設定書き込みの為のPCへの接続が必要です)
・6chの汎用I/Oを搭載


neoVI FIRE / neoVI RED の比較
NetworkProtocols / Type
neoVI RED
neoVI FIRE
 Dual Wire CAN 1-2ch (*1) 4
 Single Wire CAN 1 (*1) 1
 LSFT CAN 1 (*1) 1
 LIN 2 4
 KLine/ ISO9141/ Keyword 2K 2 4
 J1850 PWM (Class2) - 1 (*2)
 GM CGI - 1
*1: One Channel set to HS CAN, other selectable from HS/SW/LSFT CAN
*2: Total of 2 Channels


ハードウェア仕様
* neoVI 3G Architecture over 10x performance over previous devices
* 3 DSPs and 1 RISC processor for 125 MIPS of processing
* Power Consumption (typical) : 150mA @ 14.4 VDC
* Sleep Power Consumption (typical) : 12mA @ 12.0 VDC
* Power Supply: 5.5-27 Volt Power Operation
* Temperature Range: -40C to +85C
* Vehicle Connectors : 25 Pin male D-SUB and 9 Pin Male D-SUB
* Warranty: One Year Limited Warranty
* Firmware: Field upgradeable design (flash firmware)
* General Purpose IO: 6 MISC IO (0-5V on MISC 1-2 and 0 - 3.3V on MISC 3-6), 4 IO can be configured as analog
* General Purpose IO rate report interval: 1 Hz to 10 kHz or based on digital change
* General Purpose IO Maximum Current Output (Sunk/Sourced): 4mA
* Microsoft Certified USB drivers
* Isolated USB
* Stand-Alone Mode Including Scripting, Receive Messages, Transmit Messages,
* Expressions, IO, and Transport Layers
* ICS TimeSync for Multiple Hardware Synchronization supports all neoVI 3G devices
* neoVI FIRE: J2534 and RP1210 A/B compatible for CAN/ISO15765, Keyword, ISO9141, and J1850 VPW
* neoVI RED: J2534 and RP1210 A/B compatible for CAN/ISO15765, Keyword, and ISO9141
* microSD card slot support up to 2 Gigabytes of storage. The removable card is formatted
* using FAT32 for direct usage in a PC.
* Battery backed real time clock (RTC)


ネットワーク基本仕様
* 64 Bit time stamping to accuracy of 10 microseconds on CAN and LIN networks and never overflows. 0.5 microsecond accuracy timestamp available if using one network only
* Simultaneous operations on all CAN/LIN/J1850 networks
* Transmit message double-buffering on all networks allows back to back message transmission

neoVI FIRE ネットワーク仕様
6x CAN Channels
* 4 Dedicated ISO11898 Dual Wire CAN Physical Layer (TJA1040)
* 1 Dedicated ISO11519 Low Speed Fault Tolerant CAN Physical Layer (TJA1054A)
* 1 Dedicated Single Wire CAN Physical Layer GMW3089 / SAE J2411 (MC33897)
* CAN 2.0B Active
* Up to 1 M-Bit Software Selectable Baud Rate (auto baud capable)
* Capable of generating and detecting error frames
* Logic Analysis of CAN Waveform with 25 nanosecond resolution
* Graphical Bit Time / Baud Rate Calculator
* Listen only mode support
* Unterminated network detection
* High Speed Mode, Test Tool Resistor, and High Voltage Wakeup support

4x LIN (Local Interconnect), ISO9141, Keyword 2000, or K and L Line
* Full support for LIN 1.X, 2.X and J2602
* LIN J2602 / 2.X compatible physical layer
* Software Selectable LIN Master Resistor
* Capable of Generating LIN Waveforms (Including Errors) Using Dedicated Output Compare Hardware
* UART Based State Machine
* Initialization Waveforms including Fast Init, Five Baud, and Custom
* Programmable Timing Parameters including Inter-Byte, TX Inter-Frame, RX Inter-Frame and Initialization Waveforms (0.5 ms Resolution)
* Software Selectable Baud Rate
* LIN Bus Monitor Mode identifies errors : Sync Break Error State and Length, Sync Wave Error, Message ID parity, TFrameMax/Slave Not Responding, Checksum Error and Transmit Bit Errors.
* LIN Bus Master Mode operates at same time as LIN Bus Monitor
* LIN Bus Slave simulation - with or without an LDF file
* LIN Bus hardware schedule table with support for LIN diagnostics

1x J1850 VPW (GM Class 2)
* VPW Physical Layer capable of TX and RX operations in high speed modes (MC33390)
* Reception of IFR data during TX and RX
* Capable of high speed block programming

1x GM CGI
* Software Enabled (disables LIN2)
* Programmable Bit Rate
* Full block mode message reception only

neoVI RED ネットワーク仕様
2x CAN Channels
* 1 Dedicated ISO11898 Dual Wire CAN Physical Layer (TJA1040)
* 1 User Selectable ISO11898 Dual Wire CAN Physical Layer (TJA1040), SO11519 Low Speed Fault Tolerant CAN Physical Layer (TJA1054A), or Single Wire CAN Physical Layer GMW3089 / SAE J2411 (MC33897)
* CAN 2.0B Active
* Up to 1 M-Bit Software Selectable Baud Rate (auto baud capable)
* Capable of generating and detecting error frames
* Logic Analysis of CAN Waveform with 25 nanosecond resolution
* Graphical Bit Time / Baud Rate Calculator
* Listen only mode support
* Unterminated network detection
* High Speed Mode, Test Tool Resistor, and High Voltage Wakeup support

2x LIN (Local Interconnect), ISO9141, Keyword 2000, or K and L Line
* Full support for LIN 1.X, 2.X and J2602
* LIN J2602 / 2.X compatible physical layer
* Software Selectable LIN Master Resistor
* Capable of Generating LIN Waveforms (Including Errors) Using Dedicated
Output Compare Hardware
* UART Based State Machine
* Initialization Waveforms including Fast Init, Five Baud, and Custom
* Programmable Timing Parameters including Inter-Byte, TX Inter-Frame, RX Inter-Frame and Initialization Waveforms (0.5 ms Resolution)
* Software Selectable Baud Rate
* LIN Bus Monitor Mode identifies errors : Sync Break Error State and Length, Sync Wave Error, Message ID parity, TFrameMax/Slave Not Responding, Checksum Error and Transmit Bit Errors.
* LIN Bus Master Mode operates at same time as LIN Bus Monitor
* LIN Bus Slave simulation - with or without an LDF file
* LIN Bus hardware schedule table with support for LIN diagnostics


ピンアサイン
[DB25]
PIN
Description
PIN
Description
PIN
Description
1 SW CAN 10 Misc DIO 1 19 HS CAN 3 H
2 J1850 VPW 11 Misc DIO 2 20 HS CAN 3 L
3 LSFT CAN H 12 DBG DATA 21 TSYNC CLK H
4 LSFT CAN L 13 GND 22 TSYNC CLK L
5 MS CAN H 14 HS CAN 1H 23 Misc DIO 3
6 MS CAN L 15 HS CAN 1L 24 DBG RESET
7 ISO L 16 HS CAN 2H 25 VBATT
8 ISO K/LIN 1 17 HS CAN 2L    
9 DBG CLK 18 Misc DIO 4    


[DB9]
PIN
Description
PIN
Description
1 LIN 1 6 Misc DIO 5
2 LIN 2 7 Misc DIO 6
3 LIN 3 8 +3.3V(PWR CNTRL)
4 LIN 4 9 V BATT(OUT)
5 GND    




お問い合わせ先
株式会社 NEAT
愛知県名古屋市千種区池下1-11-21
TEL:052-764-3311FAX:052-764-3632

Intrepid Control Systems, Inc.
31601 Research Park Drive, Madison Heights, MI 48071 USA
Phone: (586) 731-7950 Fax: (586) 731-2274

* 記載の会社名および製品名は、各社の登録商標および商標です。

MBD・計測
リアルタイムシミュレータ
EMTP-RV
モデルベース開発
RCPシステム/ロボット
データ収録装置
車載ネットワークツール